mccli activity show -name//VirtualMachines/.
If you run into the same problem, please share your experience. If a backup job failed, you might find useful information here. I suspect the combination of removing the CDROM mapping from the virtual machine and rebooting the VDP appliance resolved the issue. I decided to try âif all else fails, reboot (the VDP appliance)â and sure enough, that did the trick. I tried the backup job a few more times all resulting in failure. As expected, I received 40 rows (five datastores x eight proxies). Starting the MCS service in VMware vSphere Data Protection 5.1.x fails with the error: gsan rollback. Next maintenance window start time: Fri Apr 5 13:00:00 2019 SGT. Next backup window start time: Fri Apr 5 21:00:00 2019 SGT. Maintenance windows scheduler capacity profile is active. This is because VDP has eight internal proxies. Solved: Hello, VDP core system is sometimes down and I usually reboot the virtual appliance of VDP (with OS shutdown). Running this command should produce approximately eight rows per datastore. Initiating the backup manually runs fine. I followed that by opening an SSH session to the appliance â ssh â where 192.168.10.51 is the IP address of my VDP appliance and running the command found in the KB article â echo âselect * from proxy_datastore_mappingâ | psql mcdb -p 5555 -U admin â which produced the output shown in the figure below. Nothing helped: rebooting the VDP, enabling/disabling the job, reconfiguring the schedule from daily to weekly and back. I tried the backup job again â this did not resolve the issue. The KB article got me started, but I thought it would be worth a blog post to elaborate a bit and share the resolution I found.Īs suggested in the KB article, I disconnected the virtual CDROM drive from the virtual machine that was causing the error (I had only a single virtual machine in the backup job that was failing). Backup SIM cards, and restore the backup if a. Naturally, I search the VMware Knowledge Base (KB) and located this article: VMware vSphere Data Protection 5.1.x fails to start backup jobs (2037003). HackerOne offers bug bounty, VDP, & pentest Compete and collaborate with top ethical hackers. Probable cause is the datastore for the virtual machine is not accessible. Re-add your folder to the job and remove the explicitly defined vms, ready for your nightly backup. I also pay attention to your comments and suggestions.I ran into an interesting vSphere Data Protection (VDP) error: Error Code 30931: Failed to initiate a backup or restore for a virtual machine. This will be a good way to run a fast snap incremental backup before an upgrade, server patch etc.without the need for a new job (and associated time and space waste). However with all these tests the backup fails, the error messages that appear are: Failed to attach disk and miscellaneous error, I do not know if it would be a good idea to modify the etc / hosts of my vcenter in Windows and to point to all the esxi in the file to verify if the backup is successful. Modify the Windows DiskEnableUUID virtual server parameter to False. The backup window starts, some VMs are made and about one hour after this starts to happen. Registration of the Vcenter in the VDP Utility Configuration, together with the restart of the VDP appliance. 21:02:46 PM: Backup job named 'VM' started. Enable internal firewall rules in the operating system to enable port 902 on both the windows server and the VDP. Run a VM vmotion storage to another datastore. Migrate these servers to all the ESXi of my infrastructure. Am I understanding that youre using both vDP for backups to. For example, missing arguments or failed connection from the MCCLI to the MCS will generate the same 23998 event (mccli command failed). backups while we hope that the next scheduled backup will complete successfully. The tests I have performed are as follows: Not all errors and failure conditions have specific event codes yet and as a result, the generic event code for a mccli command failed will be displayed. They are Windows Server 2012 R2 Standard servers. Run the consolidation and if it succeeds, re-run the VDP backup on out of date sources to remediate your. I am currently presenting the following drawback with my VDP to run backups on my virtual infrastructure, motivated that when creating the backup scheduling task, the same runs the snapshot, but at the time of creating the backup fails to 10% of having started, then removes the snapshot, but the backup fails, the maximum of the percentage that reaches is 16%. schedule backup for full backup open the tdpexcfull. The backup task failed with the return message: Backup aborted.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |